September 29,2026
Рой

Valve installation looks simple on paper—until you’re on-site, the flanges don’t line up, and the process fluid is waiting. In reality, poor installation is one of the leading causes of premature valve failure, leakage, and costly downtime. Whether you’re working with a футеровочный клапан, a сито, or a пережимной клапан, the same fundamental rules apply. This guide walks through the most frequent mistakes and how to avoid them.

Клапан Lianke

1. Misalignment and Over-Torquing

One of the most common issues is forcing a valve into a pipeline that doesn’t align naturally. This puts stress on the valve body and can crack the lining—especially critical for a футеровочный клапан. A lined valve is designed to resist aggressive chemicals, but the PTFE or PFA lining is vulnerable to mechanical damage. Always support the pipe on both sides and never use the valve bolts to pull flanges together.

Over-torquing flange bolts is another silent killer. It compresses gaskets unevenly and can distort the valve seat. Use a calibrated torque wrench and follow the manufacturer’s tightening sequence, usually a star pattern.

Пневматический пережимной клапан для тяжелых условий эксплуатации

Наш пневматический зажимной клапан повышенной прочности разработан для сложных промышленных условий, обеспечивая превосходный контроль абразивных и коррозионных сред, надежную герметизацию, минимальное техническое обслуживание и длительный срок службы. Идеально подходит для систем перекачки шлама, химических веществ и сточных вод.,

Посмотреть более подробную информацию
Пневматический пережимной клапан для тяжелых условий эксплуатации

2. Ignoring Flow Direction

Many valves are directional. A пережимной клапан is often bidirectional, but some designs perform better with flow in a specific direction to extend sleeve life. Similarly, a сито must be installed with the flow entering the designated inlet—otherwise, debris won’t be captured properly, and the screen or basket may collapse.

Always check the arrow on the valve body. If there’s no arrow, consult the manual. Installing a strainer backward is a common mistake that leads to clogged downstream equipment and unnecessary pressure drop.

3. Poor Support and Vibration

Valves are not pipe supports. A heavy футеровочный клапан or a large пережимной клапан hanging unsupported will eventually develop leaks at the flange joints. Vibration from pumps or compressors accelerates fatigue. Install pipe hangers or brackets within one pipe diameter of the valve on both sides.

For a сито, vibration can cause the basket or screen to loosen, allowing bypass of unfiltered fluid. Use a mounting bracket if the strainer is inline and heavy.

Фильтр от LIANKE

Промышленные фильтры LIANKE

Надежная фильтрация для защиты клапанов и трубопроводов — доступны типы Y, T, корзиночные и дуплексные.

Исследуйте фильтры
Промышленный фильтр LIANKE

4. Incorrect Gasket Selection

Using the wrong gasket material is a recipe for leaks. For a футеровочный клапан, the gasket must be compatible with both the lining and the process fluid. Spiral-wound gaskets with PTFE filler are common, but full-face gaskets are preferred for fragile linings to distribute bolt load evenly.

For a пережимной клапан, the sleeve is the sealing element—no gasket is needed at the flange, but the flange faces must be clean and flat. For a сито, check that the housing gasket matches the O-ring or flat gasket specified; otherwise, bypass leakage occurs.

5. Neglecting Commissioning and Maintenance Access

A valve installed in a location that’s impossible to reach for maintenance is a future headache. Leave enough space to remove the actuator, replace the пережимной клапан sleeve, or change the сито screen or basket. For a футеровочный клапан, ensure the handle or actuator can be operated without obstruction.

During commissioning, open and close each valve several times to verify smooth operation. For a сито, record the initial pressure drop. For a пережимной клапан, check that the sleeve is not pinched or twisted.

6. Forgetting Thermal Expansion

Pipelines expand and contract with temperature changes. If a футеровочный клапан is rigidly anchored between two fixed points, the thermal stress can crack the lining. Use expansion joints or loops. A пережимной клапан with an elastomeric sleeve is more forgiving, but it still needs room to move.

Заключительные мысли

Most valve installation problems come down to three things: alignment, support, and following the manual. Whether you’re installing a футеровочный клапан for corrosive service, a сито to protect downstream equipment, or a пережимной клапан for abrasive slurries, taking the time to do it right saves money and downtime.

РЕКОМЕНДУЕМЫЙ БЛОГ
October 29,2026
Рой
Why Choose Imported Industrial Valves for Harsh Working Conditions?

In heavy industries such as petroleum refining, fine chemical engineering, thermal power generation, and coal chemical industry, production systems continuously operate under harsh conditions: high temperature, high pressure, strong corrosion, high-speed fluid scouring, and flammable & explosive media. As core pressure-bearing components of pipeline fluid control systems, industrial valves directly affect operational safety, maintenance costs, […]

Читать далее
October 29,2026
Рой
How to Clean Sulfuric Acid Anti-Corrosion Storage Tanks

Anti-corrosion tanks are ideal equipment for storing corrosive liquids, and they are commonly used to contain different concentrations of acids and alkalis including sulfuric acid and hydrochloric acid. Special methods and techniques are required for cleaning sulfuric acid storage tanks. Due to the strong corrosivity of sulfuric acid, operators need to stay cautious and wear […]

Читать далее
October 21,2026
Рой
Lianke Valve Becomes a Member Unit of Wenzhou Chief Engineer Research Association

Recently, the 2nd Session of the 12th Member Congress of Wenzhou Chief Engineer Research Association was successfully held. At the meeting, Linko Valve Co., Ltd. officially joined the association as a member unit. This marks a major step forward for the enterprise in technological research & development and industry-university-research cooperation. Going forward, Linko Valve will […]

Читать далее
October 21,2026
Рой
Precision Valve Welding Craftsmanship | Superior Manual Welding at LIANKE Valve

In the professional production workshop of LIANKE Valve, a professional team of senior craftsmen devotes themselves to high-precision valve welding manufacturing. With skilled operation of welding torches and precise flame control, our experienced welders create firm, flawless weld seams for every valve body, building a solid and durable structural barrier for industrial valve products. Every […]

Читать далее
ДЛЯ ДОПОЛНИТЕЛЬНОЙ ИНФОРМАЦИИ
СВЯЗАТЬСЯ С НАМИ
Свяжитесь с Лианке +